logo

High Performance Concrete Protection and Professional Waterproofing

Italy ArabicUnitag Bulgaria Frenchfr-FR Portuguspt-PT German NorsknynorskNorway SvenskaSE English (UK)

Betonseal is the official representation of Innerseal and Topseal for Germany, Austria, Holland, Belgium and Luxemburg and is the leading company for Bio Gas Silo all over Europe.

www.betonseal.de


CONTROLL®INNERSEAL/TOPSEAL

 

TREATMENT OF CONCRETE SURFACES MULTI-STOREY CAR PARK. (CHLORIDE REHABILITATION)

A multi-storey car park concrete surfaces were treated with Controll®Innerseal and Controll®Topseal. The treated surface of concrete surfaces (C20/ 25) amounted to approximately 1.800 m2.

The concrete of a 25-year-old garage was badly damaged over the years by thaw with de-icing salt (NaCl). Corrosion damage indexed to chloride templates range in the area of the wall up to a height of 1.2 meters, and in the entire floor. The existing concrete was to be classified as hydrophilic to heavy sucking (w-value >3,0 kg/h* 0,5). The advanced carbonation (up to 40 mm) has already led to the corrosion fractures of the reinforcement bars of the load-bearing walls and concrete columns.

 

The concrete floor was mechanically release of paint, coating and epoxy linings in some areas and penetration oil with the help of Controll®Conclean remove. The 5-time application with Controll®Innerseal was the low-slung malicious brine from the concrete out transported (Gel Crystal reaction to the condensing surface), the concrete was protected permanently waterproof and against future stress by de-icing salts.

 

Here, an active remediation of chloride was created with concurrent permanent protection for the steel reinforcement and the newly installed replacement mortar. The consumption amounted to approximately  0,7  l/m2. After approximately 4 – 6 weeks, the surfaces were cleaned and sealed with Controll®Topseal. Here the consumption amounted to approximately 0.2 l / m2.

Controll®Innerseal and Controll®Topseal are non-toxic and therefore not distinguishing mark according to the hazardous substances regulation. They are colourless, odourless, solvent-free, non-flammable and bio-degradable. Leave no film coating, but a transparent, clear and natural interface.

Controll®Innerseal makes concretes resistant to chemical attack and impervious to water against both, positive and negative hydrostatic pressure, and is an active a deeply urgent corrosion protection of reinforcement steel in concrete (Deep penetration > 195 mm).  Also, any harmful salts in the mineral building material cast out during the crystallization and curing process.

Controll®Topseal includes water-soluble potassium Methylsilanetriolate with organic catalyst, which a deep penetrating allows up to 6 cm. It forms a strong water and dirt repellent surface, which is very easy to clean. The surface treated with Controll®Topseal  is still protected against efflorescence, environmental factors (air pollution) and UV rays. The chemical resistance is increased.

Beyond the product properties Controll®Innerseal and Controll®Topseal stand out due to low cost and short lay on times.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 


 

 

 

 

 

 

 

 

       
WARNING

Although the technical details and recommendations contained in this data sheet correspond to the best of our knowledge and experience, all the above information must, in every case, be taken as merely indicative and subject to confirmation after long term practical applications; for this reason, anyone who intends to use the Inner and Topseal must ensure before used that it is suitable for the envisaged application in every case.  The user alone is fully responsible for any consequences deriving from use of our products.

Komsol Innerseal products have been approved worldwide for their ability to extend the lifetime of concrete up to 3 times.